This standard is a revision of ANSI/ASQC Z,. “Sampling Procedures and Tables for Inspection by. Attributes.” Beyond editorial refinements, only the. Know the switching rules for ANSI/ASQ Z Categorize the various sampling plan systems in terms of lot-by-lot, continuous production, attributes or variables. ANSI/ASQ Z Sampling Procedures and Tables for Inspection By. Attributes The FDA recognizes ANSI/ASQ Z as a General consensus standard.

Author: Zulum Talkis
Country: Malaysia
Language: English (Spanish)
Genre: Technology
Published (Last): 24 January 2012
Pages: 248
PDF File Size: 16.52 Mb
ePub File Size: 19.12 Mb
ISBN: 506-6-99766-328-1
Downloads: 96033
Price: Free* [*Free Regsitration Required]
Uploader: Mezragore

Average sample size curves for double and multiple sampling as compared to the single sampling plan for each acceptance number are in Table IX.

ANSI/ASQ Z– (R): Sampling Procedures and Tables for Inspection by Attributes | ASQ

Once on tightened inspection, unless corrective action is taken to improve product quality, it is very likely that the rule requiring discontinuance of sampling inspection will be invoked. Rejected units may be repaired or corrected and resubmitted for inspection with the approval of, and z14.-2008 the manner speci?

Acceptance Sampling With Rectification When Inspection Errors Are Present, Journal of Quality Technology In this paper the authors consider the problem of estimating the number of nonconformances z1.4-2008 in outgoing lots after acceptance sampling with rectification when inspection errors can occur.

Zero defect sampling is an alternative method to the obsolete Mil Std E sampling scheme previously used to accept or reject products, and the remaining ANSI Z1. There are many references available that will assist you in the selection of an appropriate sampling plan based on your asni sampling risk tolerance levels.

Use of the reduced plan increases scheme probability of acceptance only for extremely low levels of percent nonconforming. If they want to know if individual units within the lot are acceptable — based on asni criteria that is considered acceptable, then the tally znsi all defects found is correct. Although individual lots with quality as bad as the AQL can be accepted with fairly high probability, the designation of an AQL does not suggest that this is necessarily a desirable quality level.


ANSI-ASQ Z Sampling Procedures and Tables for Inspection 按属性检查用取样程序_图文_百度文库

For example, my lot size is which means, under general inspection level II, the sample size would be 80 code J. The right is reserved to inspect every unit submitted by the supplier for speci?

When appropriate, the number of units in the sample shall be selected in proportion to the size of ans or subbatches, or parts of the lot asqd batch, identi? To determine acceptability of a lot or batch under percent nonconforming inspection, the applicable sampling x1.4-2008 shall be used in accordance with To me, it feels like the first step should be to determine the AQL.

Some are faster than others, and some are non-destructive. As you may already know, there are many ways to detect contamination. Inspection by attributes is inspection whereby either the unit of product is classi? The AQL alone does not describe the protection to the consumer for individual lots or batches, but more directly relates to what is expected from a series of lots or batches provided the provisions of this standard are satis?

Use single sampling plan above or alternatively use code letter E. Do I trust the acceptance sampling inspection or react? The existence of an American National Anei does not in any respect preclude anyone, whether he has approved the standard or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standard.

ASQC Q contains sampling plans that have been calculated on this basis and therefore provide a more accurate set of tables for adqc situations. When several types of plans are available for a given AQL and code letter, any one may be used. Sampling procedures and tables for inspection by attributesand there is a small section regarding inspection level clause 9. If suppliers fail to do so, there is a high probability aqsc being switched from normal inspection to tightened inspection where lot acceptance becomes more difficult.


Tag: Z1.4:2008

If that is not possible or practical, then percent inspection using a quick, inexpensive, and effective method permits you to avoid uncertainties with sampling. This chemical approach may require specialized equipment.

The unit of product may or may not be the same as the unit of purchase, supply, production, or shipment. For an AQL of 0. Inspection under the provisions of this standard shall not be resumed until corrective action has been taken. If you decide to z11.4-2008 use Z1. andi

E Acceptance Quality Limits normal inspection 1. The aswc of an AQL shall not imply that the supplier has the right to knowingly supply any nonconforming unit of product. Original inspection is the? A lot or batch is rejected; or b.

If the AQL 1.

AQL values of In the designation of inspection levels S-1 to S-4, care must be exercised to avoid AQLs inconsistent with these inspection levels. To determine the acceptability of a lot or batch under Nonconformities per Hundred Units inspection, the procedure speci? The supplier may be required at the discretion of the responsible authority to inspect every unit of the lot or batch for designated classes of nonconformities.