HT12D DATASHEET IN PDF

HT12D 2 12 Series of Decoders Features. Operating voltage: V~12V Low power and high noise immunity CMOS Built-in oscillator needs only 5% resistor. IC HT12D can be used only with its pair HT12E. These two ICs together form an Encoder and Decoder pair. They are bit. HT12D Datasheet, HT12D Holtek Decoder Datasheet, buy HT12D Decoder IC.

Author: Tojalabar Samulmaran
Country: Myanmar
Language: English (Spanish)
Genre: Art
Published (Last): 25 August 2006
Pages: 404
PDF File Size: 14.48 Mb
ePub File Size: 12.82 Mb
ISBN: 122-5-79257-647-8
Downloads: 24072
Price: Free* [*Free Regsitration Required]
Uploader: Shakatilar

HT12D is capable of decoding 12 bits, of which 8 are address bits and 4 are data bits. In simple terms, HT12D converts the serial ht12 into parallel outputs. This oscillator can be used by connecting these two pins through a 1M Resistor 17 Valid Transmission VT This pin will go high when a data is received. The 4-bit data that is received can be obtained on pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7.

Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc. So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you.

Choosing Motor For Robots. Arduino based GPS receiver. Interface SD Card with Arduino. Virgin Galactic — Commercial Space Flight. To know how a 4-bit data can be encoded and then send to the input pin of this IC, we have to understand the working of the HT12E Encoder IC which is given here.

  ALPHA CD32C MANUAL PDF

Supply voltage; 5V 2. Valid transmission; active high. In the above circuit I have set the 8-bit address data as 0b, datasheeg connecting all address pins to ground. They are paired with 2 12 series of encoders. It decodes the serial addresses and data received by, say, an RF receiver, into parallel data and sends them to output data pins.

HT12D/HT12F – Product Details – Holtek

Connected to the Ground of circuit. The IC datasheeh should be powered by 5V pin 18 and the ground pin pin 9 is grounded.

This series of decoders are mainly used for remote control system applications, like burglar ratasheet, car door controller, security system etc.

This oscillator can be used by connecting these two pins through a 1M Resistor. The IC has a built in oscillator. Submitted by admin on 27 October TL — Programmable Reference Voltage.

HT12D is a decoder integrated circuit that belongs to 2 12 series of decoders. Choosing Battery for Robots. What is Web Browser. SPI Module of Arduino. These are the 8-bit address bits, which is used to protect your data. This pin powers the IC should use only 5V. A valid transmission in indicated by a high signal at VT pin. We should set the bits in same pattern on Encoder and Decoder IC to pair them.

The Encoded 12 bit output data obtained from HT12E has to be given here. A basic circuit diagram for the HT12D IC is datasheeg below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.

  FORSAKEN DEMON TRAPPERS PDF

HT12D Decoder IC

If any valid data is received they can be obtained from these four pins. These two ICs together form an Encoder and Decoder pair. Skip to main content. They can also datahseet connected to LED to physically view the received data.

For decoding a data the IC will requires an oscillatorluckily this IC has one in-built. This high-density System-in-Package SiP integrates controller, power switches, and support components. Interface GPS with Arduino. The input data code is decoded when no error or unmatched codes inn found.

HT12D Datasheet

It kn mainly provided to interface RF and infrared circuits. The data on 4 bit latch type output pins remain unchanged until new is received. It is not mandatory to use it. So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data.

It is very important that your Decoder should have the same address of that of the encoder. This pin will go high when a data is received. The serial input data is compared with the datadheet addresses three times continuously.